|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
MicroPowerTM Microprocessor Reset Circuit General Description The AAT3532 PowerManagerTM product is a member of AATI's Total Power ManagementTM IC (TPM ICTM) product family. It is a fully integrated device for monitoring microprocessor activity, external reset, and power supply conditions. The device holds the microprocessor in a reset condition for a minimum of 250ms while VCC is established to ensure correct system start-up. A manual reset can be initiated via a debounced input pin. As an additional level of protection, the AAT3532 includes a watchdog timer which requires a periodic strobe input from the microprocessor to ensure correct operation. The AAT3532 has a programmable watchdog timer and voltage tolerance level. The quiescent supply current is extremely low, typically 23A. The AAT3532 is available in an 8-pin SOP package specified over -40 to 85C temperature range. AAT3532 Features * * * * * * * * * * PowerManagerTM Adjustable 4.5V or 4.75V Voltage Monitor 250ms (min) Reset Pulse Width Low quiescent current: typically 23A Adjustable Watchdog Timer (150ms, 600ms, or 1200ms) De-bounced Manual Reset Input Operates down to 20ns strobe input pulse width No external components Temp range -40 to 85C Standard 8 pin SOP package Pin compatible with MAX1232 Applications * * * * * * Computers Controllers Telecom Equipment Embedded Systems Intelligent Instrumentation Automotive Typical Application VDD VCC PBRST RST RESET INPUT VDD AAT3532 TD RST ST I/O P TOL GND 3532.2004.07.1.1 1 MicroPowerTM Microprocessor Reset Circuit Pin Descriptions Pin # 1 2 3 4 5 AAT3532 Symbol PBRST TD TOL GND RST Function Pushbutton reset input. A de-bounced active low input for manual reset. Guaranteed to recognize inputs 20ms or greater. Watchdog time delay set input. See Table 1 for watchdog timeout selections. Tolerance set. Input selects 5% or 10% threshold detection IC ground connection Reset Output (active high). Activated when either: VCC falls below the reset voltage threshold, or PBRST is forced low, or ST not strobed within the minimum timeout period, or during power-up. Reset Output (active low, open drain). Inverse of RST. Strobe input to watchdog timer. A pulse is required within watchdog timeout period to prevent RST and RST entering active state 5V Supply 6 7 8 RST ST Vcc Pin Programming Selections TD Pin GND Float VCC Time-Out Min 62.5ms 250ms 500ms Typ 150ms 600ms 1200ms Max 250ms 1000ms 2000ms Table 1: TD Pin Programming for Watchdog Timeout Selections TOL Pin VCC GND Tolerance 10% 5% Table 2: Reset Voltage Threshold Programming Selections Pin Configuration SOP-8 (Top View) PBRST TD TOL GND 1 8 VCC ST RST RST 1 2 2 7 3 6 4 5 2 3532.2004.07.1.1 MicroPowerTM Microprocessor Reset Circuit Absolute Maximum Ratings Symbol VCC VI/O TA TS TLEAD VESD (TA=25C unless otherwise noted) AAT3532 Description VCC to GND Voltage on I/O pins relative to GND Operating Temperature Range Storage Temperature Range Maximum Soldering Temperature (at Leads) for 10s ESD Rating1--HBM Value -0.5 to 6 -0.5 to (VCC+0.5) -40 to 85 -65 to 150 300 2000 Units V V C C C V Note: Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. Functional operation at conditions other than the operating conditions specified is not implied. Only one Absolute Maximum rating should be applied at any one time. Note 1: Human body model is a 100pF capacitor discharged through a 1.5k resistor into each pin. Thermal Characteristics Symbol JA PD Description Maximum Thermal Resistance2 Maximum Power Dissipation 2 Value 100 1.25 Units C/W W Note 2: Mounted on an FR4 board. 3532.2004.07.1.1 3 MicroPowerTM Microprocessor Reset Circuit DC Electrical Characteristics Typical values are at TA=25C) Symbol VCC IQ VCCTP IIL IOH IOL VIH VIL IRST AAT3532 (VIN = 4.5V to 5.5V, TA = -40 to 85C unless otherwise noted. Description Supply Voltage Quiescent Current1 Reset Threshold 5% Reset Threshold 10% Input Leakage ST, TOL Output Current RST2 Current RST2, RST ST and PBRST Input High ST and PBRST Input Low RST Output Leakage Conditions VCC = 5.5V TOL = GND TOL = VCC VOH = 2.4V VOL = 0.4V CMOS Levels TTL Levels Min 4.5 Typ 5.0 23 160 4.62 4.37 Max 5.5 50 500 4.74 4.49 1.0 Units V A V V A mA mA V V A 4.50 4.25 -1.0 -8.0 10.0 2.0 -0.3 VOH = VCC VCC+0.3 0.8 1.0 AC Electrical Characteristics Typical values are at TA=25C) Symbol CIN COUT tPB tPBD tRST tST tTD tf tr tRPD tRPU (VIN = 4.5V to 5.5V, TA = -40 to 85C unless otherwise noted. Description Input Capacitance ST, TOL Output Capacitance RST, RST3 PBRST4 PBRST Delay Reset Active Time ST Pulse Width 3 Conditions TA = 25C TA = 25C Fig 2 Fig 2 Fig 3 TD Pin = 0V TD Pin = Open TD Pin = VCC 4.75V to 4.25V 4.25V to 4.75V VCC Falling VCC Rising Min Typ Max 5 7 Units pF pF ms ms ms ns ms ms ms s s s ms ST Time-out Period VCC VCC VCC VCC Fall Time3 Rise Time3 Detect to RST High and RST Low Detect to RST Low and RST Open 20 1 250 20 62.5 250 500 10 0 250 4 610 150 600 1200 5 610 20 1000 250 1000 2000 50 1000 Notes: 1. Measured with outputs open and ST toggling at 100kHz, 50% duty cycle 2. RST is an open drain output 3. Guaranteed by design and not subject to production testing. 4. PBRST must remain low for greater than 20ms to guarantee a reset 4 3532.2004.07.1.1 MicroPowerTM Microprocessor Reset Circuit Functional Block Diagram VCC VCC Tolerance Select AAT3532 TOL Reset Generator RST RST VREF PBRST ST TD De-Bounce Circuit Watchdog Timer Detector Watchdog Timer GND Applications Information Power Monitor The reset function monitors the VCC supply to ensure a microprocessor is correctly reset and is powered up into a known condition following a power supply failure. RST and RST will remain valid for Vcc voltages down to 1.4V. The RST and RST pins are asserted whenever VCC drops below the reset threshold voltage. This volt- age can be set by programming the TOL pin. Connecting TOL to VCC sets the 10% tolerance of the VCC supply (typically 4.37V for VCC = 5V). Connecting TOL to GND sets the 5% tolerance of the VCC supply (typically 4.62V for VCC = 5V). The reset pin is guaranteed to remain asserted for a minimum period of 250ms after VCC has risen above the reset threshold voltage. RST output is an open drain output. For correct operation, a pull-up resistor of 10k should be connected between this output and VCC. +5V +4.75V (5% Trip Point) VCC +4.50V (10% Trip Point) 0V RESET output delay (VCC Rising) tRPU RST tRPD RESET output delay (VCC Falling) RST Figure 1. Reset Output Delay 3532.2004.07.1.1 5 MicroPowerTM Microprocessor Reset Circuit Applications Information Manual Reset The PBRST pin makes it possible to manually reset the system by either directly connecting a mechanical push-button between the PBRST pin and GND or connecting to a logic low output. Internal de-bounce circuitry is provided to reduce the effect of noise glitches at the input. The signal should remain low for a minimum of 20ms for correct operation. Once the PBRST signal is released (or goes to a logic high), RESET (RESET) remains asserted for a minimum of 250ms. AAT3532 tPB tPBD PBRST tRST RESET RESET Figure 2 Push-button Reset Watchdog Timer The watchdog timer monitors the microprocessor to ensure that the system is functioning correctly. The ST pin of the AAT3532 can be derived from the microprocessor data signals, address signals, and/or I/O signals. The watchdog timer function forces the RST and RST signals into the active state when the ST input is not toggled by a predetermined time. This time period is set by the logic state of the TD pin as shown in Table 1. The timer starts once the RST signals become inactive. If the watchdog timer does not receive a high-to-low transition within the specified timeout period, then the RST signals are activated for a minimum 250ms. In normal operation the timer should receive a transition from the microprocessor within the timeout period, in which case the timer is reset and normal operation continues. The AAT3532 will accept and recognize ST pulses down to a minimum of 20ns wide. tST ST tTD Figure 3. Watchdog Input 6 3532.2004.07.1.1 MicroPowerTM Microprocessor Reset Circuit Ordering Information Package SOP-8 Marking1 3532 Part Number (Tape and Reel) AAT3532IAS-T1 AAT3532 Note: Sample stock is generally held on all part numbers listed in BOLD. Package Information SOP-8 3.90 0.10 4.90 0.10 6.00 0.20 0.375 0.125 45 1.55 0.20 0.175 0.075 4 4 0.235 0.045 0.825 0.445 0.42 0.09 x 8 1.27 BSC All dimensions in millimeters. 3532.2004.07.1.1 7 MicroPowerTM Microprocessor Reset Circuit AAT3532 AnalogicTech cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in an AnalogicTech product. No circuit patent licenses, copyrights, mask work rights, or other intellectual property rights are implied. AnalogicTech reserves the right to make changes to their products or specifications or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. AnalogicTech warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with AnalogicTech's standard warranty. Testing and other quality control techniques are utilized to the extent AnalogicTech deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed. Advanced Analogic Technologies, Inc. 830 E. Arques Avenue, Sunnyvale, CA 94085 Phone (408) 737-4600 Fax (408) 737-4611 8 3532.2004.07.1.1 |
Price & Availability of AAT3532 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |